How to Make a Karaoke Version of a Song
November 9, 2026 · 6 min read · by the ClipCraft team
To make a karaoke version of a song you need the instrumental: the full backing with the lead vocal pulled out, so someone can sing over the top. Worth saying that plainly up front, because the tool most people grab for this, a vocal remover, tends to do the opposite of what you would guess. ClipCraft's Vocal Extractor hands you the vocal by itself. So this is the honest version of the guide. Where ClipCraft gets you a real karaoke track, where it can't, and what to do instead.
What a karaoke track actually is
Two parts, really. First, the music with the lead vocal removed, so nothing competes with the singer in the room. Second, the words on screen, timed to the beat, so the singer knows when to come in. Get both and you have karaoke. The hard part is almost always the first one, and it's where the tool you reach for matters.
Why a vocal remover is the wrong first move
Our Vocal Extractor runs an AI separation model called Demucs. It listens to a finished mix and splits it apart. The catch is what we hand back: the tool is set to keep the vocal and drop the instruments. Drop a song in and about a minute later you get a clean acapella, in one of two flavors. Vocals only, or Vocals + faint backing, which leaves a little of the music underneath.

You see the cost before anything runs. A 2:30 song reads 30 tokens, because it charges 10 tokens per started minute. The free plan covers a run, the paid plans go up from there, and if you want a burst there are roll-over token packs that never expire. One run caps at 3 minutes of audio on every plan except Studio. Small honest quirk I keep noticing: the button that starts it still reads Remove background music, but the file that lands in your downloads is the vocal, not the backing. If the vocal really is what you're after, that's covered in the extract-vocals guide, and there's a wider roundup in the best vocal removers comparison.
The clean way to make a karaoke version of a song
Here is where ClipCraft is genuinely good at this: when the song is yours. If you built it in SoundCraft, or made it with an AI tool like Suno and kept the parts, a karaoke version is a two-minute job and it sounds perfect, because you never separate anything. Each instrument already lives on its own track. You just switch off the one you don't want.
- Open SoundCraft and load each part of the song onto its own channel, or just open the project you made it in.
- Find the vocal channel and click the round power button at its left edge. It grays out and drops straight out of playback and the export.
- Open the Export dialog and leave Render track on Master, the whole mix. Pick WAV for lossless or MP3 for a small file.
- What comes out is your instrumental, with no separation artifacts to clean up.


The editors are free, so you can sign up and do this today without spending a single token. No separation, no ghosting in the chorus, just the mix with one track switched off. If you have never used the DAW, the SoundCraft walkthrough covers the basics.
Songs you didn't make: the honest limits
What if you only have the finished MP3 of someone else's song, with no separate parts? Straight answer: there is no button in ClipCraft that hands you a clean instrumental of a finished mix right now. Ours keeps the vocal and drops the backing, which is the wrong direction for karaoke.
The classic do-it-yourself trick is phase cancellation. You line up the original mix against an inverted copy of the isolated vocal, sum them, and the vocal roughly cancels out, leaving a rough instrumental behind. It only half-works even in theory, because a separated vocal is never a bit-perfect copy of the vocal in the original, so you get swirly artifacts wherever the two disagree. And it doesn't work in ClipCraft anyway: SoundCraft has no polarity or phase-invert control, and the volume fader bottoms out at silence rather than going negative. I could dress up a workaround here, but it would be fake, so I won't.
There's also the old center-channel trick, where you cancel whatever sits dead center in the stereo field. It does remove a centered vocal, but it removes the kick, the snare and the bass along with it, since those usually live in the center too. The backing comes out thin and lopsided. SoundCraft doesn't do that, and honestly you wouldn't want it to.
Add the words on screen
Once you have an instrumental, the second half of karaoke is the lyrics, timed to the music. The Video Captions tool has an audio-to-video mode built for this: feed it your instrumental (or the full song for a sing-along reference), pick a size and a background, type the lyrics or let it auto-caption them, and it burns the words onto a video you can export. The full walkthrough is in the lyric-video guide.
What the acapella is actually good for
Since the extractor gives you the vocal, here's where that's the right tool instead of the wrong one:
- Practice against a real lead. Solo the extracted vocal and learn how the original singer phrases against the beat before you record your own take.
- Sample a line you love and build something new around it.
- Lay the vocal over your own instrumental in SoundCraft, then post the result to the ClipCraft music feed.
- Study a mix by hearing the vocal on its own, reverb and all.
So the honest summary is short. If the song is yours, muting the vocal channel and exporting the mix gives you a real karaoke instrumental in a couple of minutes, and you can start in SoundCraft right now. If it's someone else's finished track, ClipCraft gives you the acapella, not the instrumental, and I would rather tell you that than sell you a workaround that ghosts.
Make your next song karaoke-ready
Sign up free, build a track in SoundCraft, and export the instrumental by switching one channel off. The editors are free forever; you only spend tokens on AI compute.
Open SoundCraft free